NAME of TEST STANDART PRICE
(EU/Pie)
EXPLANATIONS
MECHANICAL TEST LABORATORY
Tensile Test TS EN ISO 6892-1* 35




50
(for 1200 - 2500 kN )
30 kN
600 kN
2500 kN
(Screw and BoltM6, M8, M16
Rebar Ø8 - Ø56
Round or Flat 1 - 100 mm thickness)
TS EN ISO 15630-1*
TS EN ISO 15630-2
TS EN ISO 15630-3
TS 708*
ISO15835-2
BS4449*
BS6744
BS4482
BS4483
ASTM A370*, ASTM E8
ASTMA615/615-M
ASTM A706 / A706M
DIN 488-2
NEN 6008/BRL0501
NBN A 24 - 301
NF A35 - 80-1
Comprehension Test DIN 50156 35  
Fatigue Test (High Frequency) TS EN ISO 15630-1* 450
(2x10^6 Cycle)

550
(5x10^6 Cycle)

1.100
(10x10^6 Cycle)
(Capacity 500 kN
 Rebar, 5,5-40 mm,
Bolt M5, M6, M8, M10, M12,
M14,M16, M20, M24, M30)
TS 708*
BS 4449*
BS 6744
DIN 488-2*
BRL 0501(NEEN 6008)*
EN 10080
ISO 15835
Fatigue Test (Low Frequency) SI 4446 175 (Capacity 850 kN,
10 Cycle at 3 Hz)
SI739
UNE36065
PN-H-93220
EN ISO 15835
Rib Geometry TS EN ISO 15630-1* 35 (Dimensional and Geometrical Measurements)
TS 708*
BS 4449*
DIN 488-2
BRL 0501(NEN 6008)*
NBN A24-301
NF A35-80-1
ASTMA615/615-M
Bend Test TS EN ISO 15630-1* 20
(Bending)

                 
30
(Bending
Rebending)
((10-50 mm Bending
Rebending Test)
TS EN ISO 15630-2
TS EN ISO 15630-3
TS 708*
TS ISO 5173
BS 4449*
BS6744
BS4482
BS4483
DIN 488-2
BRL 0501(NEEN 6008)
EN ISO 7438
ASTM A 370
ASTMA615/615M
ASTM A706 / A706M
NBN A24-301
NF A35-80-1
3 Point Bend Test TS 205-1 EN ISO 7438* 100  
ASTME290
Charpy Impact Test TS EN ISO 148-1* 35
(Room Temp)  
50
(0 / -40 C°)
100
(-40 / -80 C°)
(From Room Temperature to -80 C°)
ASTM E23
 
CHEMICAL and COAL ANALYSIS LABORATORY
Chemical Analysis Sample Preparation ASTM E1806* 45 Chemical Analysis in Ferrous Materials by Optical Emission Spectrometer (C, Mn, Si, P, S, Ni, Cr, Cu, Mo, V, Ti, Al, Nb, W, As, Sn, Co, Pb, B, Sb, Ta, Zr, Bi, Ca, Mg, Se, Te, Zn, Ce, La, N, O, Fe)
TS EN ISO 14284*
Chemical Analysis -Plain Carbon and Low Alloy Steel ASTM E415*
Chemical Analysis - Stainless Steel ASTM E1086*
Chemical Analysis - High Manganese Steel ASTM E2209*
Chemical Analysis - Cast Iron ASTM E1999
Coal Sample Preparation ASTM D2013/D2013M* 25  
TS 4744*
Total Moisture in Coal ISO 589-B2* 35  
Inherent Moisture in Coal ASTM D7582* 35 If only volatile matter or ash analysis is asked, inherent moisture, total moisture and sample preparation prices are added. Unit price is 25 euro per parameter.
Ash Analysis in Coal ASTM D7582* 35
Volatile Matter Analysis in Coal ASTM D7582* 35
Fixed Carbon Analysis in Coal ASTM D7582* 25
Loss on Ignition in Ash ASTM D7348 35  
Total Sulphur in Coal ASTM D4239* 40 If only total sulphur, total carbon or hydrogen analysis is asked, inherent moisture and sample preparation prices are added.
Total Carbon Analysis in Coal ASTM D5373* 25
Hydrogen Analysis in Coal ASTM D5373* 25
Calorific Value Analysis TS ISO 1928* 55 If only Calorific Value is asked, sample preparation, inherent moisture, total moisture, total sulphur and hydrogen analysis are added
 
MICROSTRUCTURE AND MATERIALS ANALYSIS LABORATORY
Microstructure Examination ASTM E3
ASTM E45*/ ISO 4967
ASTM E112*/ ISO 643
80 Inclusion in Metalic Materials
Grain Size and Phase Analysis
Microstructure and Failure Analysis
Macrostructure Examination ASTM E3*
ASTM E381*
65 8x-40x Magnification by Stereo Microscope
Macro Materials Inspection
Scanning Electron Microscope (SEM) Examination for 1 hour 90 Macrostructure and Failure Analysis
Local and regional Chemical Analysis by EDS
Macro Hardness Measurement TS EN ISO 6506*/ ASTM E10
TS EN ISO 6507*/ ASTM E384
TS EN ISO 6508*/ ASTM E18
30 Brinell, Vickers and Rockwell
Hardness Measurement (2,5-187,5 kg.f)
Brinel Hardness Measurement on Cast Materials up to 3000 kg.f
Micro Hardness Measurement TS EN ISO 6507*/ ASTM E384 60 Mikro Vickers Hardness Measurements and Hardness Scanning
HV 0,01-2
Jominy Test ISO 642* 135 Jominy Test including Heat Treatment and HRC Hardenability Curve Curve Graph
ASTM A255* 175
Sample Preparation for Metallography Sample Cutting 10 Applied to Macro Hardness and SEM samples when Sample Preparation is required
Mounting 15
SEM Conductive Mounting 20
Coating Thickness Measurement Optical Method 55 Measurement by Optical Microscope (Coatings; Zinc, tin, Chromium, painted plate etc.)
 
PILOT SCALE STEEL MILL SIMULATION LABORATORY
Induction Furnace (Melting/Casting Max. 50 kg) Price will be defined according
to the project.
Heat Treatment (Max. 1300 C°)
Rolling Mill Simulation (Long Products)
Rolling Mill Simulation (Flat Products)

(*) THESE TESTS ARE DONE WITIN THE SCOPE OF 17025 ACCREDITATION